气液混输泵用双螺杆泵配75kw-4电机
![](http://img.11467.com/null.jpg)
更新时间:2016-09-11 09:47:57
价格:¥12500/台
品牌:泊远东
型号:W7.3Z75Z1MbW81
联系电话:0317-8185077
联系手机:13831765644
联系人:陶春霞
让卖家联系我
详细介绍
●双螺杆泵系列产品分为单吸双螺杆泵和双吸双螺杆泵两大类。该系列产品具有特殊的螺杆型线和与之配套的特殊结构,广泛适用于石油、化工、冶金、钢铁、电力、船舶、制药、食品、建材等各种行业,其适用介质之多、输送范围之广、应用工况之复杂是其它泵类产品无法比拟的。这些特点也使得该系列泵具有潜在的使用发展前景。Double screw pump series products are divided into single suction of two kinds of double screw pump and double suction double screw pump.This series of products have special screw lines and form a complete set with the special structure, widely used in petroleum, chemical industry, metallurgy, steel, electricity, shipbuilding, pharmaceutical, food, building materials and other industries, by as much as its applicable medium, transmission range wide, application condition of the complex is unmatched by other pump product.These features also makes the use of this series of pumps with potential development prospects.
●泵体内装有两根左、有施单头螺纹的螺杆,主动螺杆2由动力机驱动转动时,靠同步齿轮1带动从动螺杆3转动。两根螺杆以及螺杆与泵体. 之间存在着间隙,该间隙靠齿轮和轴承保证。其间隙大小,取决于液体粘度、工作压力等因素。由于每根螺杆两端螺纹的旋向相反,螺杆转动时,由螺杆啮合线形成的泵工作腔。Equipped with two left in the pump body, a single thread screw, active screw driven by engine 2 turns, driven by synchronous gear 1 driven screw 3 rotation.Two screw and screw and pump body. There is a gap between the gap by gear and bearing.The gap size, depends on the liquid viscosity, pressure and other factors.Because each thread rotate to the opposite on both ends of the screw, the screw rotates, formed by the screw meshing line pump working chamber.
●气液混输泵采用双吸式结构,螺杆两端处于同一压力腔中,轴向力可以自行平衡。两端轴承采用外装式,单独采用润滑油(脂)润滑,因而不受输送介质的影响。两螺杆间用一对同步齿轮驱动,螺杆齿面间并不接触,而留有一微小间隙,介质中的杂质并不能对螺杆齿面产生直接的磨损(除冲刷外)。 除一些小排量泵外(2W.W4.0以下),一般在泵体上都带有内流式安全阀,当排放压力超过额定值时,有一定的保护作用。 泵体上的进出口方向有两种,一为水平进,水平出;二为水平进,垂直向上出;用户可根据自己需要选择。This type pump adopts double suction type structure, at the same pressure in the cavity on both ends of the screw, the axial force can balance itself.Both ends of bearing mounted outside using, lubricated by lubricating oil (grease) separately, and therefore not affected by the medium.With a pair of synchronous gears drive between the two screw, the screw does not contact between tooth surfaces, and leave a small gap, the impurities in medium can not be directly on the screw tooth surface wear (except wash).Except a few small displacement pump (below 2 w. W4.0), generally contain flow relief valve on the pump body, when the discharge pressure exceeds rating, has certain protective effect.There are two kinds of the direction of the import and export on the pump body, one for level, level;Secondly, level, vertical;User can choose according to their own needs.
●气液混输泵性能参数的选择:
1. 流量 Q :
作为容积式泵,影响双螺杆泵流量的因素主要有转速 n ,压力 p ,以及介质的粘度 v 。The selection of performance parameters:
1. The flow Q:
As a positive displacement pump, double screw pump flow effects are the major factors of rotational speed n, pressure p, and the medium viscosity v.
1.1 转速 n 的影响:
气液混输泵(高温双螺杆泵,大流量双螺杆泵)在工作时,两螺杆及衬套之间形成密封腔,螺杆每转动一周便由进口向出口移出一个密封腔,即一个密封腔的体积的液体被排出去。理想状态下,泵内部无泄漏,那么泵的流量与转速成正比。即: Qth=n*q n---- 转速; q---- 理论排量,即泵每转一周所排出的液体体积; Qth---- 理论排量。The influence of the rotational speed n 1.1:Screw pump (high temperature double screw pump, large flow of double screw pump) at work, the sealed cavity formed between the two screw and bushing, the screw rotation per week will remove a sealed cavity from import to export, that is, a sealed cavity volume of liquid is out.Internal leak-off ideally, pump, the pump flow rate is proportional to the speed.Namely: Qth q = n * n - speed;Q - the theory of displacement, the pump discharge by turn every week liquid volume;Qth - the theory of displacement.
1.2 压力 △ P 的影响:
双螺杆泵(高温双螺杆泵,大流量双螺杆泵)实际工作过程中,其内部存在泄漏,也称滑移量。由于泵的密封腔有一定的间隙,且密封腔前、后存在压差 △ P ,因此,有一部分液体回流,即存在泄漏,泄漏量用 △ Q 表示,则 Q=Qth- △ Q.显而易见,随着密封腔前、后压差 △ P 升高,泄漏量 △ Q 逐渐增大。对于不同型线和结构,影响大小也各不相同。The influence of pressure delta P 1.2:
Double screw pump (high temperature double screw pump, large flow of double screw pump) in the process of the actual work, its internal is leaking, also known as slippage.Due to pump seal chamber has a certain gap, and seal chamber before and after the differential delta P, as a result, some liquid reflux, is leakage, leakage in delta Q, Q = Qth - delta Q. Obviously, as the seal chamber pressure difference before and after the delta P increases, leakage delta Q increases gradually.For different lines and structure, effect size are different.
1.3 粘度 v 的影响:试想:将清水和粘稠的浆糊以相同的体积从漏斗式的容器中泄漏出去。显然水比浆糊要泄漏得快。同理,对于双螺杆泵,粘度大的流体比粘度小的液体的泄漏要小,泄漏量与介质粘度有一定的比例关系。,要综合地考虑以上各种因素,通过一系列的计算才能地知道泵的实际流量是否符合工况要求。The influence of the viscosity of 1.3 v: just think: will clear water and the volume of the sticky paste with the same leak out from the funnel type of container.Obviously water leak faster than paste.Similarly, for double screw pump, the viscosity of the fluid is larger than that of low viscosity liquid leakage, leakage and the proportion of medium viscosity have a certain relationship.Above all, should be synthetically considered the above factors, through a series of calculations to accurately know the actual flow of the pump is in accordance with the working condition requirements.
2. 压力 △ P :
与离心泵不同,双螺杆泵的工作压力 △ P 由出口负载决定,即出口阻力来决定。出口阻力与泵的出口处的压力是匹配的,出口阻力越大,工作压力也越大。若想知道压力,则需要用流体力学的知识对出口阻力的计算。2. Pressure delta P:
Unlike centrifugal pump, double screw pump working pressure delta P is determined by export load, namely export resistance to decide.Export resistance is matching with the pump outlet pressure, export the resistance, the greater the pressure of work.If want to know the pressure, you may need to drag on exports by the knowledge of fluid mechanics calculations.
3. 轴功率 N :
气液混输泵(高温双螺杆泵,大流量双螺杆泵)的轴功率分为两部分,即: Nth---- 液压功率,即压力液体的能量; Nr---- 摩擦功率。3. The shaft power N:
Double screw pump (high temperature double screw pump, large flow of double screw pump) of the shaft power is divided into two parts, i.e., the Nth, hydraulic power, namely of liquid pressure energy;Nr - friction power.
对于确定的压力和流量,其液压功率是一定的,因此影响轴功率的因素为摩擦率 Nr 。
摩擦功率是由于运动部件的摩擦而消耗的那部分功率。这些摩擦功率显然是随着工作压差的增加而增加的,并且介质粘度的增加也会引起液体摩擦功率的增加。To determine the pressure and flow rate, the hydraulic power is certain, so the influence of shaft power factor for the friction ratio of Nr.Friction power is due to the friction in the moving parts and the part of the power consumption.The friction power is obviously increases with the increase of the pressure difference, and the increase of viscosity of medium can also cause the liquid friction power increases.
由此,泵的轴功率除了液压功率外,其中摩擦功率随介质粘度及工作压力而增加,因此在选择配套电机时,介质的粘度也是一个非常重要的参考数据。尤其在输送高粘度介质时,需要作比较的计算。Thus, the pump shaft power in addition to the hydraulic power, the friction power increases with medium viscosity and the pressure of work, therefore, when choosing motor medium viscosity is also a very important reference data.Especially in transport high viscosity medium, the need for accurate calculation.
在计算功率后,选择配套电机时应遵照样本表格中所规定的有关规定。
N(KW) N≤10 10 < N≤50 N > 50 N > 100 K 1.5 1.25 1.15 1.1 Nm=N.K Nm---- 电机功率 N---- 轴功率 K---- 功率储备系数
4. 吸上性能的计算及选择 :泵(高温双螺杆泵,大流量双螺杆泵)工作分为以下几个阶段: 4. On the absorption performance of calculation and selection: pump (high temperature double screw pump, large flow of double screw pump) work is divided into the following stages:
4.1 吸入,此时液体连续不断地沿吸入管道移动;the liquid move continuously along the suction piping;
4.2 旋转的螺杆把能量传给工作液体;rotary screw liquid energy to work;
4.3 压出,此时液体带有克服压出管道系统所有阻力所必需的压力从泵中排出。pressure, the liquid with necessary to overcome all delivery pipeline system pressure from the eduction in pump.
在以上三个阶段中,Zui为重要的阶段是必须保证泵的吸上条件,泵才能正常工作,这是泵工作的重要条件,否则就会发生气蚀,即引起振动,噪音等问题。 In the above three stages, the most important stage is must ensure that the suction on the condition of the pump, pump can work normally, this is the important condition of pump work, otherwise cavitation occurs, which cause vibration, noise and other issues.
双螺杆泵相关业绩:
输送糖蜜泵
W2KSE-34W63变频减速整机 配电机:YCJ71-2.2KW-399 流量:1.3m3/h 压力:0.5Mpa
港口卸油泵:
W6.4ZK90Z1M1W73双螺杆泵; 配电机:Y280S-4-75KW 流量:100m3/h;压力:1.0Mpa
V6.4Zi-75M3W73立式双螺杆泵;配电机:Y37KW-4;流量:100m3/h;压力:0.6Mpa
码头卸油泵:
W6.4ZK-75Z3M1W73双螺杆泵;配电机:YB45KW-4;流量:100m3/h;压力:0.6
W7.2 ZK-43M1W73双螺杆泵;配电机:YB75KW-4;流量:100m3/h;压力:0.6Mpa
W7.2ZK57Z1M1W73双螺杆泵;配电机:YH55KW-4;流量:100m3/h;压力:0.8Mpa
原油中转泵:
W7.3Z75Z1MbW81双螺杆泵;配电机:YVP75KW-6;流量:100m3/h;压力:1.0Mpa
W6.4ZK90Z1M1W73双螺杆泵;配电机:YX3-75KW-4;流量:100m3/h;压力:1.0Mpa
W6.4ZK-90Z3M1W73双螺杆泵;配电机:Y75KW-4;流量:107m3/h;压力:1.2Mpa
轻柴油供油泵
W4.1ZK27M1W73双螺杆泵;配电机:Y22KW-4;流量:10m3/h;压力:2.0Mpa
W4.1ZK27M1W73双螺杆泵;配电机:YB22KW-4;流量:10m3/h;压力:2.0Mpa
W3.1ZK-30Z1M1W73双螺杆泵;配电机:YB7.5KW-4;流量:10m3/h;压力:0.4Mpa
输送液体硫磺泵
W5kse-40M2W78双螺杆泵;配电机:YBVP11KW-6;流量:10m3/h;压力:0.3Mpa
W7.3ZK-75Z0M1W80双螺杆泵;配电机:Y315-6B3;流量:110m3/h;压力:0.6Mpa
W6.4ZK-100M1W75双螺杆泵;配电机:YBH37KW-4;流量:118m3/h;压力:0.6Mpa
W6.4ZK-90M1W73双螺杆泵;配电机:Y37KW-4;流量:120m3/h;压力:0.4Mpa
输送沥青泵
V7.2Zi-57M3W73双螺杆泵;配电机:Y45KW-4;流量:120m3/h;压力:0.6MPa
W7.2ZK-57Z1M1W72双螺杆泵;配电机:YB132KW-4;流量:120m3/h;压力:2.5Mpa
W6.4ZK-100Z3M1W73双螺杆泵;配电机:YB18.5KW-4;流量:131m3/h;压力:0.2Mpa
沥青混合料专用泵
W3.1ZK-40M1W74双螺杆泵;配电机:YB7.5KW-4;流量:13m3/h;压力:0.4Mpa
W3.1ZK-40M1W73双螺杆泵;配电机:YB7.5KW-4;流量:15m3/h;压力:0.4Mpa
W7.3Z112MbW80双螺杆泵;配电机:Y90KW-6;流量:166M3/H;压力:1.0Mpa
W7.3Z112MbW80双螺杆泵;配电机:YB90KW-6;流量:166m3/h;压力:1.0Mpa
齿轮箱滑油泵
V7.2ZK-75Z1M1W73双螺杆泵;配电机:YH110KW-4;流量:168m3/h;压力:
W2.1ZK-24M1W73双螺杆泵;配电机:YH132S-6-3KW;流量:2.4m3/h;压力:0.6Mpa
W7.2ZK-94M1W73双螺杆泵;配电机:Y90KW-4;流量:200m3/h;压力:1.0Mpa
高粘度液体泵
W7.2ZK-94Z2M1-W75双螺杆泵;配电机:YB2 75KW-4;流量:200m3/h;压力:0.62Mpa
W7.2ZK-94M1W72A双螺杆泵;配电机:YH90KW-4;流量:200m3/h;压力:0.8Mpa
W5.2Z40Z1MbW81双螺杆泵;配电机:Y30KW-6;流量:20m3/h;压力:1.0Mpa
W3.1ZK-58Z1M1W73双螺杆;配电机:YB11KW-4;流量:20m3/h;压力:0.4Mpa
输送石蜡泵
W4.1ZK-48M1W73双螺杆泵;配电机:Y15KW-4;流量:25m3/h;压力:0.4Mpa
W5kse-65M4W75双螺杆泵;配电机:YB11KW-4;流量:25m3/h;压力:0.5Mpa
MW6.5ZK25Z0M1W81双螺杆泵;配电机:YB250M-4B3-55KW;流量:25m3/h;压力:4Mpa
抽石蜡泵
W4.1ZK-56M1W75双螺杆泵;配电机:YBH15KW-4;流量:26.5m3/h;压力:0.8Mpa
W4.1ZK56M1W73双螺杆泵;配电机:YB15KW-4;流量:26.6m3/h;压力:0.8Mpa
W7T.3Z-130Z0MBW80双螺杆泵;配电机:Y355S-6;流量:263;压力:1.2
W7.2ZK124Z1M1W73双螺杆泵;配电机:YB45KW-4;流量:270m3/h;压力:0.23Mpa
W7T.3Z-85Z0MBW80双螺杆泵;配电机:Y315L1-4;流量:273;压力:1.2
W7T.2ZK28M1W73双螺杆泵;配电机:Y132KW-4;流量:28m3/h;压力:3.5Mpa
W2kse-24M1W63双螺杆泵;配电机:YB1.5KW-4;流量:2m3/h;压力:0.4Mpa
抽沥青泵
W2.1ZK-14Z2M1W73双螺杆泵;配电机:YB100L2-4B3D;流量:3.4;压力:0.4
W7T.2ZK-94Z1M1W73双螺杆泵;配电机:YB110KW-4;流量:300m3/h;压力:0.6Mpa
W7.2ZK-112M1W73双螺杆泵;配电机:YH132KW-4;流量:300m3/h;压力:0.8Mpa
抽粘胶液泵
W6kse-50M4W75双螺杆泵;配电机:YB11KW-4;流量:30m3/h;压力:0.5Mpa
W5kse-65M2W63双螺杆泵;配电机:YHB15KW-4;流量:30m3/h;压力:0.6Mpa
W6kse-30M4W77双螺杆泵;配电机:Y37KW-2;流量:39.7m3/h;压力:1.2Mpa
抽重质燃油泵
W2.1ZK-14M1W82双螺杆泵;配电机:Y2.2KW-4;流量:3m3/h;压力:0.4Mpa
W3kse-40M1W77双螺杆泵;配电机:YB4KW-6;流量:3m3/h;压力:1Mpa
W4.2Z70Z1MbW81双螺杆泵;配电机:Y180L-4-22KW;流量:40m3/h;压力:1.0Mpa
W6kse-67M4W75双螺杆泵;配电机:YB15KW-4;流量:40m3/h;压力:0.5Mpa
油气混输泵
W4.2Z70Z1MbW81双螺杆泵;配电机:YX3-22KW-4;流量:40m3/h;压力:1.0Mpa
W5.1ZK-54M1W73双螺杆泵;配电机:YB22KW-4;流量:44m3/h;压力:0.8Mpa
W5.2ZK-78M1W80双螺杆泵;配电机:Y45KW-6;流量:45m3/h;压力:1.5Mpa
抽煤焦油泵
W5.1ZK-54M1W73双螺杆泵;配电机:Y75KW-4;流量:45m3/h;压力:2.5MPa
W3.1ZK-20Z3M1W73双螺杆泵;配电机:YB4KW-4;流量:5.1m3/h;压力:0.5Mpa
W8.4ZK-67M1W73双螺杆泵;配电机:YH200KW-4;流量:500m3/h;压力:0.8Mpa
W8.4ZK85M1W72双螺杆泵;配电机:YH280KW-4;流量:500m3/h;压力:1.0Mpa
抽炭黑油泵
抽炭黑油泵
W8.5ZK-100Z0M1W84双螺杆泵;配电机:YH355M-4B3-220KW;流量:500m3/h;压力:0.8Mpa
W5.1ZK65Z1M1W73双螺杆泵;配电机:Y30KW-4P;流量:50m3/h;压力:1Mpa
W5.1ZK65Z1M1W78双螺杆泵;配电机:Y30KW-4P;流量:50m3/h;压力:1Mpa
W5.1ZK-54Z1M1W77双螺杆泵;配电机:YB18.5-4;流量:50m3/h;压力:0.2Mpa
抽改性沥青泵
W4.2ZK-78Z0M1W80双螺杆泵;配电机:YB22KW-4;流量:50m3/h;压力:0.6Mpa
W7kse-75M2W78双螺杆泵;配电机:YBVP22KW-6;流量:50m3/h;压力:0.2Mpa
W6.5Z-67Z0MBW80双螺杆泵;配电机:Y250M-6;流量:54;压力:1.2
W6.4ZK-62M1W60A双螺杆泵;配电机:Y37KW-4;流量:55m3/h;压力:1.0Mpa
抽SBS沥青改性剂泵
W5.2Z-65Z0MBW80双螺杆泵;配电机:Y225M-4;流量:57;压力:1.2
W5.1ZK78M1W73双螺杆泵;配电机:Y37KW-4;流量:60m3/h;压力:1.0Mpa
W5.2Z-65Z1M1W80双螺杆泵;配电机:YB45KW-4;流量:60m3/h;压力:0.7Mpa
W8.4ZK-100Z3M1W73双螺杆泵;配电机:YB132KW-4;流量:614m3/h;压力:0.2Mapa
输送原油泵
W8.5ZK-112M1W82A双螺杆泵;配电机:YH250KW-4;流量:650m3/h;压力:0.8Mpa
W6.5Z-75Mb1W80双螺杆泵;配电机:Y15KW-6;流量:66m3/h;压力:0.1Mpa
W5.1Z-78M1W73双螺杆泵;配电机:YB45KW-4;流量:69.6 m3/h;压力:1Mpa
输送乳化沥青泵
W2.1ZK-34M1W73双螺杆泵;配电机:YB4KW-4;流量:6m3/h;压力:0.6Mpa
W3.1ZK-20Z2M1W73双螺杆泵;配电机:Y132S-4B3D;流量:7.1;压力:0.4
W6.4ZK75Z1M1W73双螺杆泵;配电机:YB37KW-4;流量:78m3/h;压力:0.8Mpa
输送重油泵
W2.1ZK-34M1W73双螺杆泵;配电机:YB7.5KW-4;流量:8.9m3/h;压力:0.6Mpa
W6.4Zi62Z1M1W73双螺杆泵;配电机:Y225M-4-45KW;流量:80m3/h;压力:1.0Mpa
W6.4ZK62Z1M1W73双螺杆泵;配电机:Y45KW-4;流量:80m3/h;压力:1.0Mpa
高粘度打胶泵
W6.5Z100MbW81双螺杆泵;配电机:Y55KW-6;流量:80m3/h;压力:1.0Mpa
W6.4ZK62Z1M1W77双螺杆泵;配电机:YB30KW-4;流量:80m3/h;压力:0.3Mpa
W6.4ZK-62M1W73双螺杆泵;配电机:YB75KW-4;流量:80m3/h;压力:2.0Mpa
沥青混合料专用泵
W6.5ZK-75Z0M1W84双螺杆泵;配电机:YH225S-4B3-37KW;流量:80m3/h;压力:0.8Mpa
W6.5Z100Z1MbW81双螺杆泵;配电机:YVP55KW-6;流量:80m3/h;压力:1.0Mpa
W6.5Z100MbW81双螺杆泵;配电机:YVP55KW-6;流量:80m3/h;压力:1.0Mpa
燃油输送泵
W6.4ZK62Z1M1W73双螺杆泵;配电机:YX3-45KW-4;流量:80m3/h;压力:1.0Mpa
W6.4ZK-100Z3M1W77双螺杆泵;配电机:Y55KW-6;流量:88m3/h;压力:1.0Mpa
W4kse-48M1W77双螺杆泵;配电机:YB7.5KW-6;流量:8m3/h;压力:1Mpa
相关产品
联系方式
- 地址:广州 河北省泊头市道东街88号
- 邮编:062150
- 电话:0317-8185077
- 销售经理:陶春霞
- 手机:13831765644
- 传真:0317-8185455
- QQ:253061203
- Email:253061203@qq.com
产品分类
站内搜索