卸油泵用KCB18.3齿轮泵流量1.1
KCB-18.3(2CY-1.1/14.5)流量:1.1m3/h,压力:1.45Mpa,吸入真空高度5米,口径:G3/4",配电机Y90L-4●KCB齿轮泵概述
KCB齿轮油泵在输油系统中可用作传输、增压泵;KCB gear oil pump in the oil system can be used as a transport, booster pump;
在燃油系统中可用作输送、加压、喷射的燃油泵;In the fuel system can be used as a transport, pressure, jet fuel pump;
在一切工业领域中,均可作润滑油泵用。In all industrial areas, can be used as lubricating oil pump.
KCB齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。齿轮经热处理有较高的硬度和强度,与轴一同安装在可更换的轴套内运转。泵内全部零件的润滑均在泵工作时利用输出介质而自动达到。KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal. Gear after heat treatment with high hardness and strength, and shaft installed in the replaceable shaft sleeve. In all parts of the lubrication pump are pump work automatically to achieve using the output media.
泵内有设计合理的泄油和回油槽,是齿轮在工作中承受的扭矩力Zui小,因此轴承负荷小,磨损小,泵效率高。Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.
泵设有安全阀作为超载保护,安全阀的全回流压力为泵额定排除压力的1.5倍,也可在允许排出压力范围内根据实际需要另外调整。但注意本安全阀不能作减压阀的长期工作,需要时可在管路上另行安装。从主轴外伸端向泵看,为顺时针旋转。Pump is equipped with safety valve as overload protection, the total reflux pressure relief valve is rated pump out pressure of 1.5 times, also can allow discharge pressure range according to actual needs and adjust. But note that this cannot be a long-term work pressure reducing valve, relief valve can be installed in the piping shall be separately when necessary. To pump from the main shaft overhang end to see, for clockwise.
●KCB齿轮泵性能范围
流量:1.1m3/h-600m3/h压力:0.28MPa--2.5MPa Traffic: 1.1 m3 / h - 600 m3 / h pressure: 0.28 MPa, 2.5 MPa
主要用于油田、油库、港口、码头、船舶等大流量输油,卸油!Mainly used in oil fields, oil depot, ports, docks, ship big flow like oil, oil unloading
应用范围:KCB/2CY型齿轮输油泵适用于输送粘度在300c.s.t以下的各种油类,如原油、柴油、润滑油、动植物油等。配用铜齿轮可输送低闪点液体,如汽油、苯等。介质温度不超过70℃,耐高温油泵的使用温度不超过300℃。本泵身带有安全阀,超载时起安全作用。轴封有骨架油封、机械密封、填料密封三种型式,订货注明。KCB齿轮润滑泵主要用于各种机械设备中的润滑系统中输送润滑油,适用于输送粘度在10oE(75c.s.t)以下,温度在300℃以下的具有润滑性的油料,不锈钢齿轮泵可输送食用油料、饮料等。轴封有骨架油封、机械密封、填料密封三种型式.Scope of application: KCB type / 2 cy gear oil pump is suitable for conveying viscosity at 300 c. S.t under various oil, such as crude oil, diesel oil, lubricating oil, animal and plant oil. With copper gear can handle liquid low flash point, such as gasoline, benzene, etc. Medium temperature does not exceed 70 ℃, the use of high temperature resistant oil pump temperature does not exceed 300 ℃. When the pump body with a safety valve, overloading security role. Shaft seal skeleton oil seal, mechanical seal, packing three type, indicate the order. KCB gear lubrication pump is mainly used for all kinds of mechanical equipment of conveying lubricating oil in the lubricating system, suitable for conveying viscosity in 10 oe (below 75 c. S.t), the temperature is below 300 ℃ with lubrication oil, stainless steel pump can transport edible oil, beverage and so on. Shaft seal skeleton oil seal, mechanical seal, packing three types.
●KCB齿轮泵安装说明:
1、安装泵的地点应足够宽敞,以方便检修工作。2、泵安装的好坏,对泵的平稳运行和使用寿命有很重要的影响,所以安装校正工作必须仔细地进行,不得草率行事。3、泵吸入管的安装高度、长度和管径应满足计算值,力求简短,减少不必要的损失(如弯头等);并保证泵在工作时,不超过其允许汽蚀余量。4、吸入和排出管路应该有支架。泵不允许承受管路的负荷。KCB gear pump installation instructions: 1, the location of the installation of pump should be spacious enough, to facilitate maintenance and repair work. The stand or fall of 2, pump installation, for the smooth running of the pump and service life have very important influence, so the installation calibration work must be carried out carefully and must not be too hasty. 3, installation height of pump suction pipe, the length and diameter should satisfy the calculated value, to short, reduce unnecessary losses, such as elbow, etc.); And ensure the pump at work, no more than the allowed NPSH. 4, suction and discharge line should be a support. Pump are not allowed to bear load of pipeline.
●KCB齿轮泵安装顺序: KCB gear pump installation order:
1、在安装过程中,为防止杂物落入机器内,机组的所有孔眼均应盖好。1, during the installation process, so as to prevent debris into the machine, all perforation should cover of the unit.
2、在接好管路及确定电动机转动方向后,再接上联轴器,并再校核一遍轴的同心度。2, good on the line and determine the direction of motor rotation, and coupling is connected, check it again and shaft concentricity.
3、校正泵轴和电机轴的同心度,在联轴大路外圆上,允许偏差0.1毫米;两联轴器平面的间隙应保证2~4毫米,(小泵取小值)间隙要均匀,允差0.3毫米。3, calibration of pump shaft and motor shaft concentricity, cylindrical, along the road in coupling allowable deviation of 0.1 mm;In the plane of the two coupling gap should guarantee 2 ~ 4 mm, small little pump (in value) clearance wants even, tolerance of 0.3 mm.
4、将机组放在埋有地脚螺栓的基础上,在底座与基础之间,用成对的楔垫用校正用。4, put the unit in buried with anchor bolt, on the basis of between the base and foundation, with pairs of wedge cushion with correction.
5、为防止管线中杂物进入泵内,对新安装的管线,在泵胶应装设过滤器,其有效截面应大于吸入管截面的2~3倍。5, in order to prevent debris into the pump in the pipeline, pipeline of new installation glue should be installed in the pump filters, the effective cross section should be greater than the suction pipe section 2 ~ 3 times.
6、松开联轴大,用水平仪分别放在泵轴和底座上,通过调整楔垫,校正机组水平,适当拧紧地脚螺栓,以防走动。6, loose coupling, use level on the pump shaft and base, respectively, by adjusting the wedge cushion, correction unit level, tighten the anchor bolts, just in case.
7、在机组实际试运行2~3小时后,作Zui后检查,如无不良现象,则认为安装合格。
7, in the actual commissioning unit 2 ~ 3 hours later, a final inspection, if there is no negative phenomenon, is considered qualified installation.
●kcb齿轮泵的结构:KCB gear pump structure:
泵主要有泵体、齿轮、轴、轴承、安全阀、前盖、后盖、密封部件、联轴器部件组成。设有安全阀的泵、当排油管路的液压值超过泵的规定时,安全阀开启,保证泵及原动机不致因压力过高而受到损坏。轴端密封有三种形式:填料密封、机械密封、橡胶圈密封,用户可根据具体的使用条件选择合适的密封结构。泵有良好的自吸性,泵内运动部件利用输送的液体实现润滑,致工作时可以不加引液和润滑剂。Mainly include pump body, pump gear, shaft, bearing, relief, front cover, back cover, sealing parts, clutch parts.Is equipped with safety valve pump, when the discharge of oil pipeline hydraulic value exceeds the rules of the pump, relief valve open, ensure the pump and prime mover from damaged because the pressure was too high.Shaft end seal has three forms: packing seal, mechanical seal, rubber ring seal, the user can choose according to the specific conditions of use suitable sealing structure.Good self-priming pump, pump inside the moving parts using conveying fluid lubrication, can not add lead to work fluid and lubricant.
高粘度耐酸泵 | SNF120R46U12.1W2三螺杆泵 | 大庆高新技术产业开发区南天实业有限公司 |
糖蜜输送泵 | SNF660R54U12.1W21三螺杆泵 | 株洲兴隆化工实业有限公司 |
润滑油输送泵 | G20-1V-W112单螺杆泵 | 河北盛华化工有限公司 |
重油输送泵 | SNGF80R46G10W21泵头 | 河北精信化工集团有限公司 |
输送粘胶液泵 | G85-1V-W101单螺杆泵 | 四川川恒化工股份有限公司 |
输送涂料泵 | NYP220-RU-T1-J-W11高粘度泵 | 中国平煤能源化工集团飞行化工有限公司 |
锅炉燃烧器供油泵 | SNH120R54U12.1W21三螺杆泵 | 通化化工股份有限公司 |
桐油输送泵 | SNH120R46E6.7W21三螺杆泵 | 浙江华泰塑胶股份有限公司 |
焦油输送泵 | G70-1V-W101单螺杆泵 | 甘肃银达化工有限公司 |
输送糖蜜泵 | SNH120R46U12.1W2三螺杆泵 | 临沂久泰能源化工有限公司 |
粘胶输送泵 | SNH120R46U12.1W2三螺杆泵 | 南宁化工股份有限公司 |
液体蜡输送泵 | SNH1300R42U12.1W21三螺杆泵 | 湖北嘉辉化工集团有限公司 |
原油输送泵 | 2CY2/0.33齿轮泵 | 德州实华化工有限公司 |
沥青输送泵 | SNH1700R46E6.7W21三螺杆泵 | 山东海王化工股份有限公司 |
输送高速柴油泵 | SNH210R40E6.7YW21三螺杆泵 | 山东潍坊润丰化工有限公司 |
合成液压油输送泵 | G20-1V-W101单螺杆泵 | 张家港化工机械股份有限公司 |
倒油泵 | 2CY1.1齿轮泵 | 大连金州重型机器有限公司 |
输送柴油降凝剂泵 | 3GR36*6AW21三螺杆泵 | 大庆华科股份有限公司 |
输送汽轮机油泵 | 3GR42*4AW21CCS船用泵 | 成都华融化工有限公司 |
船用低压燃油泵 | 3GR42*6AW21CCS船用泵 | 石家庄白龙化工股份有限公司 |
输送润滑脂泵 | 3GR50*2W21三螺杆泵 | 上海联恒异氰酸酯有限公司 |
输送基础油泵 | 3GR50*4W21三螺杆泵 | 南京化纤股份有限公司 |
输送齿轮油泵 | 3GCR50*2W21三螺杆泵 | 镇江李长荣综合石化工业有限公司 |
稀油站润滑油泵 | 3GC50*3W21三螺杆泵 | 贵州省遵义碱厂 |
输送柴油泵 | 3GR70*2W21三螺杆泵 | 山东单县化工有限公司 |
联系方式
- 地址:广州 河北省泊头市道东街88号
- 邮编:062150
- 电话:0317-8185077
- 销售经理:陶春霞
- 手机:13831765644
- 传真:0317-8185455
- QQ:253061203
- Email:253061203@qq.com